Description
The
VIPSeal VE059-045 flexible adaptor is a stepped
50mm to 40mm waste reducer designed to join compatible plain-ended waste and low-pressure pipework of different outside diameters. Commonly used as a
2 inch to 1.5 inch adaptor, this
50-59mm to 38-45mm coupling provides a practical
flexible waste pipe reducer for repairs, alterations and refurbishment work. The VE059-045 has two different connection ranges. The larger side accepts compatible pipe with an outside diameter from 50mm to 59mm, while the smaller side accepts pipe measuring approximately 38mm to 45mm.
VIPSeal VE059-045 Flexible Adaptor
The
VIPSeal VE059-045 flexible adaptor is the genuine product reference for this stepped reducer within VIPSeal’s earlier flexible sanitary adaptor range. Unlike a straight coupling, the
VIPSeal VE059-045 flexible adaptor deliberately has two different connection diameters, allowing larger waste pipe to transition into smaller compatible pipework.
Choosing the VIPSeal VE059-045 Flexible Adaptor
Choose the
VIPSeal VE059-045 flexible adaptor where the larger pipe outside diameter falls between 50mm and 59mm and the smaller pipe measures between approximately 38mm and 45mm. Measure the actual outside diameter of both pipes before ordering rather than relying solely on nominal descriptions such as 50mm, 40mm, 2 inch or 1½ inch.
Installing the VIPSeal VE059-045 Flexible Adaptor
Before fitting the
VIPSeal VE059-045 flexible adaptor, clean both pipe ends and remove dirt, grease, burrs and damaged material. Position the stepped adaptor correctly between the two pipes and tighten the stainless-steel clamp bands evenly. Make sure the surrounding pipework is adequately supported before testing the completed joint.
50mm to 40mm Waste Reducer
The VE059-045 is commonly used as a
50mm to 40mm waste reducer where larger waste pipe needs to transition into smaller 40mm pipework. A
50mm to 40mm waste reducer can be useful on bathroom, utility, commercial waste and maintenance installations where a rigid reducer is difficult to fit or where existing pipe positions allow little movement.
Using a 50mm to 40mm Waste Reducer
When using the product as a
50mm to 40mm waste reducer, check both actual pipe outside diameters. Nominal waste-pipe sizes do not always correspond exactly to the physical dimensions of every pipe system.
2 Inch to 1.5 Inch Adaptor
The VE059-045 is also commonly described as a
2 inch to 1.5 inch adaptor, providing a flexible transition between compatible nominal 2 inch and 1½ inch pipework. The
2 inch to 1.5 inch adaptor can be especially useful when repairing existing installations where replacing a complete run with matching rigid fittings would be inconvenient.
2 Inch to 1.5 Inch Adaptor Applications
Typical uses for the
2 inch to 1.5 inch adaptor include waste-pipe alterations, plumbing repairs, refurbishment work and joining compatible plain-ended pipework of different sizes.
50-59mm to 38-45mm Coupling
The
50-59mm to 38-45mm coupling is selected according to the actual pipe outside diameter rather than nominal pipe size alone.
- Larger connection range: 50–59mm O/D
- Smaller connection range: 38–45mm O/D
- Configuration: stepped reducing adaptor
The stepped construction of the
50-59mm to 38-45mm coupling allows two significantly different pipe diameters to be connected within one flexible fitting.
Selecting a 50-59mm to 38-45mm Coupling
Both pipes should sit comfortably within their respective connection ranges. If either pipe is outside the specified measurements, choose another flexible coupling or adaptor rather than forcing the VE059-045 onto unsuitable pipework.
Flexible Waste Pipe Reducer
The VE059-045 provides a useful
flexible waste pipe reducer for joining plain-ended waste pipework where a conventional rigid reducer cannot easily be installed. The
flexible waste pipe reducer can accommodate small dimensional and alignment variations while the separate clamp bands secure each end around the corresponding pipe.
Flexible Waste Pipe Reducer for Repairs
A
flexible waste pipe reducer is particularly useful during maintenance work because it allows pipe sizes to be adapted without solvent welding or rebuilding a larger section of the existing system.
Flexible PVC Stepped Construction
Legacy exact-code documentation identifies VE059-045 as a flexible PVC sanitary adaptor. Its stepped body reduces between the two different pipe outside-diameter ranges. This flexible construction provides more dimensional tolerance than a rigid moulded reducer and makes the fitting useful across compatible waste and low-pressure drainage installations.
Stainless-Steel Clamp Bands
The VE059-045 uses stainless-steel clamp bands to mechanically secure the flexible adaptor around each pipe end. Each side can therefore be secured independently around its corresponding pipe diameter.
Waste, Soil, Vent and Drainage Applications
The
VIPSeal VE059-045 flexible adaptor can be useful for applications including:
- 50mm to 40mm waste-pipe reductions
- 2 inch to 1½ inch pipe transitions
- Sink, bath and utility waste alterations
- Commercial waste pipework
- Joining compatible plain-ended pipes of different sizes
- Repairing damaged or cut pipe sections
- Low-pressure drainage connections
- Maintenance and refurbishment work
Stepped Adaptor vs Straight Coupling
VE059-045 is a reducing adaptor rather than a straight coupling. If both pipes have approximately the same outside diameter, use a suitable straight flexible coupling. Choose VE059-045 where its different 50–59mm and 38–45mm ranges are actually required.
Legacy VE Flexible Adaptor Range
The VE059-045 belongs to VIPSeal’s earlier flexible sanitary adaptor range. It should therefore be listed using specifications confirmed for this exact VE product rather than automatically inheriting the EPDM material, operating temperatures or pressure ratings of newer VIPSeal VAC and VIPSealPlumb products.
VIPSeal VE059-045 Flexible Adaptor Key Features
- Genuine VIPSeal VE059-045 product reference
- Flexible stepped reducing adaptor
- Larger pipe O/D range: 50–59mm
- Smaller pipe O/D range: 38–45mm
- Common nominal connection: 50mm to 40mm
- Common imperial description: 2 inch to 1½ inch
- Flexible PVC construction
- Stainless-steel clamp bands
- Suitable for compatible waste and low-pressure pipework
- Useful for repair, alteration and refurbishment work
Shop Flexible Pipe Connectors
Browse our
Flexible Connectors range for flexible couplings, reducers, adaptors and specialist pipe repair fittings. For current manufacturer technical resources, see the official
VIPSeal Product Documentation library. The
VIPSeal VE059-045 flexible adaptor provides a versatile
50mm to 40mm waste reducer and
2 inch to 1.5 inch adaptor, using a
50-59mm to 38-45mm coupling design to create a practical
flexible waste pipe reducer.
